%all.entities; ]> $Date: 2023-04-21 02:00:16 +0000 (Fri, 21 Apr 2023) $ VBoxManage-metrics 1 VBoxManage-metrics monitor system resource usage &product-name; VBoxManage metrics collect --detach --list --period=seconds --samples=count * host vmname metric-list VBoxManage metrics disable --list * host vmname metric-list VBoxManage metrics enable --list * host vmname metric-list VBoxManage metrics list * host vmname metric-list VBoxManage metrics query * host vmname metric-list VBoxManage metrics setup --list --period seconds --samples count * host vmname metric-list The VBoxManage metrics command enables you to monitor system resource usage for the host system and for virtual machines (VMs). For example, you can monitor particular metrics, such as the percentage of time CPUs spend executing in user mode (CPU/Load/User) over a specified sampling period. While it runs, the VBoxSVC process collects and saves the specified metric data internally. The VBoxSVC process runs until shortly after you close all VMs and frontends. Use the VBoxManage metrics query command to retrieve data at any time. By default, metrics are not collected unless you run the VBoxManage metrics setup command to specify a sampling interval in seconds and the number of metrics to save. Note that you can enable metric collection only for started VMs. Collected data and collection settings for a VM are discarded when the VM shuts down. The host and VMs have different sets of associated metrics, which you can view by running the VBoxManage metrics list command. Each metric is represented as a string that is composed of a category and a metric. Optionally, the metric string can include any of the following: a submetric, a sub-submetric, and an aggregate. The metric string has the following format: category/metric[/submetric[/sub-submetric]][:aggregate] category is the resource type, such as CPU, RAM, FS, Net. metric is a measurement type that is associated with the resource category. For example, the Load and MHz metrics are associated with the CPU resource category. submetric is an optional measurement type that is associated with the metric. For example, the User, Kernel, and Idle submetrics are associated with the Load metric. sub-submetric is an optional measurement type that is associated with the submetric. For example, the Rx and Tx sub-submetrics are associated with the Rate submetric of the Net resource category. The associated metric is the network interface. aggregate is an optional function to provide minimum, maximum, and average measurements for a resource category. For example, the RAM/Usage/Free:min metric represents the minimum amount of available memory found in all saved data on the host system. By default, the VBoxManage metrics commands operate on the host system and all VMs, and report on all metrics. You can optionally limit these commands to operate on the host system or on a particular VM, and report on a list of one or more metrics. * | host | vmname Specifies the component on which to operate. By default, this command operates on the host system and all running VMs. If you specify host, the VBoxManage metrics command operates on the host system only. If you specify an asterisk (*), the command operates on all VMs. If you specify the name of a VM, the VBoxManage metrics command operates on that VM. metric-list Specifies a comma-separated list of one or more metrics. The form of the metric must include the category and metric part of the metric string separated by a slash. Note that the VBoxManage metrics enable and VBoxManage metrics disable commands require that you specify metrics as parameters. The metrics must include only the resource category and metric part, such as CPU/Load and RAM/Usage. The VBoxManage metrics collect command collects and outputs data periodically until you stop the process by pressing Ctrl+C. --detach Disables the collection of metric data, so no data is output. Using this option is the same as running the VBoxManage metrics setup command. --list Shows which metrics match the specified filter. --period=seconds Specifies the number of seconds to wait between collecting metric data samples. The default value is 1. --samples=count Specifies the number of metric data samples to save. To view the saved data, use the VBoxManage metrics query command. The default value is 1. The VBoxManage metrics disable command suspends data collection. This action does not affect the data collection properties or the collected data. Note that specifying a submetric in the metric list does not disable its underlying metrics. Note that the VBoxManage metrics disable command requires that you specify metrics as parameters. The metrics must include only the resource category and metric part, such as CPU/Load and RAM/Usage. --list Shows whether the command succeeded as expected. The VBoxManage metrics enable command resumes data collection after it has been suspended by using the VBoxManage metrics disable command. Note that specifying a submetric in the metric list does not enable its underlying metrics. Unlike the VBoxManage metrics setup command, the VBoxManage metrics enable command does not discard previously collected samples for the specified set of objects and metrics. Note that the VBoxManage metrics enable command requires that you specify metrics as parameters. The metrics must include only the resource category and metric part, such as CPU/Load and RAM/Usage. --list Shows whether the command succeeded as expected. The VBoxManage metrics list command shows the metrics that are currently available. Note that VM-specific metrics are shown only when that VM is running. The VBoxManage metrics query command retrieves and shows the saved metric data. Note that the VBoxManage metrics query command does not remove or flush saved data but older samples are replaced by newer samples over time. The VBoxManage metrics setup command configures metric-gathering properties. Note that this command discards any previously collected samples for the specified set of objects and metrics. To enable or disable metrics collection without discarding the data, use the VBoxManage metrics enable command or the VBoxManage metrics disable command, respectively. --list Shows which metrics have been modified as a result of the command execution. --period=seconds Specifies the number of seconds to wait between collecting metric data samples. The default value is 1. --samples=count Specifies the number of metric data samples to save. To view the saved data, use the VBoxManage metrics query command. The default value is 1. The following example command enables the collection of host processor and memory usage metrics every second. The --samples option saves the five latest samples. $ VBoxManage metrics setup --period 1 --samples 5 host CPU/Load,RAM/Usage The following command lists the metrics that are available to the host system and VMs: $ VBoxManage metrics list Note that the host system and VMs have different sets of metrics. The following example shows how to query metric data about the CPU time spent in user and kernel modes for the test VM: $ VBoxManage metrics query test CPU/Load/User,CPU/Load/Kernel